INCISOGRAFO MG 2.5

From continuous research and innovation comes the MG 2.5 Engraver

We implement in our Engravers the best technology available on the market today to make high-precision machines that are easy to use and fast in execution.

The adoption of motors with integrated ethercat drives allows us to continuously monitor the health of the machine and be able to intervene, even remotely, to solve any problems.


Technical Characteristics

Main Features:

  1. Work Area: 2330x1200mm
  2. Z-axis movement: 200mm
  3. Electrospindle with Internal Pressurization and ISO-30 cone seat
  4. 3D Acquisition Laser
  5. Tool Calibration Sensor
  6. Remote Control for Fine Positioning
  7. Tool Warehouse with 10 Workstations
  8. Software INCX

Electrical and Pneumatic Demands

Incisografo:

  1. Three-phase voltage 400 v - 5-pole 16A socket (3 phases + neutral + ground) for the machine body
  2. 7 Kw/h during operation, with 10 Kw/h peak
  3. 0.3mA delayed differential
  4. Dehumidified and filtered compressed air with pressure up to 7bar (6 for engaging and disengaging tools from the electrospindle)

Dust Extractor (optional):

  1. Three-phase voltage 400 v - 4-pole 16A socket (3 phases + ground) for vacuum cleaner
  2. 6 Kw/h for Dust Extractor
  3. 6 bar for Dust Extractor


Spindle

The ISO 30 electrospindle, capable of up to 12,000 rpm and equipped with internal pressurization to safeguard the ball bearings from dust infiltration.

The electrospindle can also work with water tip cooling.

Motor with Integrated Ethercat Driver

The machine uses brushless motors with integrated Ethercat drives.

This allows us to be able to monitor the correct operation of the machine at all times and to be able to take targeted action if problems occur.

3D Acquisition Laser

The 3D capture laser is used both to acquire bas-reliefs or 3D models and to survey the surface of the plate to be engraved.

Once the surface is acquired, the machine will lay the engraving on it, thus enabling perfect execution even on uneven surfaces.

Tool Calibration Sensor

The calibration sensor is used just before execution to detect how much the tool protrudes from the ISO-30 taper.

With this information, the INCX software is able to correctly lay the tool on the plate surface for execution with perfect depth.

CyberHead

The CyberHead: a specially designed suction mouth to suck up the most dust during engraving and thus safeguard the cutting edge of the tool as much as possible.

The CyberHead can be opened by remote control to control execution in real time.

The CyberHead is also available for tool cooling with water nozzles.

Frequently Asked Questions

What is the difference between MI 2.5 and MG 2.5?

The difference is only in the size of the actual working area. While the MG has a working area of 2300x1200mm, the MI can engrave on an area of 1350x1200mm with the possibility of engraving even plates of a size larger by being able to insert it and slide it sideways.

Is it very difficult to learn how to use the Engraver?

The Engraver consists of three pieces of software: the machine control software, the Incimar composer, and the Aspire design program.

The course for the Incimar control software takes about 2 hours, for the Incimar composer 2 hours, and for the Aspire software 4 to 8 hours, depending on the customer's experience with cad/cam environments.

Incimar staff, however, is always available to intervene even by tele-assistance in case of doubts or problems.

Why work dry?

The use of water, besides being wasteful, is highly overrated in the field of artistic engraving on marble, while it may make sense in engraving on materials such as granite or hard stone.

Our Engravers are set up to be able to adopt water cooling as well, but if most of the work is on marble or "soft" stones we can safely say that the use of water is not absolutely necessary and that the tool can safely engrave even large bas-reliefs without suffering.

en_GB